ROOFCRYL

Request a Quote
Download TDS

DESCRIPTION

Roofcryl is a single component water based 100% acrylic smooth waterproof coating.

SPECIFICATION

ROOFCRYL is a single component, water based, 100% acrylic waterproof coating designed to provide durable protection to concrete and metal substrates. It forms a flexible, breathable membrane with excellent adhesion, high UV resistance and superior light reflectance exceeding 91%. The product contains approximately 60% solids by weight and offers strong mechanical performance, including resistance to wind-driven rain, fungus growth and impact. It achieves adhesion values of about 6.5 N/mmΒ² on concrete and 6.3 N/mmΒ² on steel, with touch dry time of 1–2 hours and recoating after approximately 6 hours under standard conditions.

APPROVALS / CERTIFICATES

USES

To avoid damp and water leakage risk, it’s recommended for:

  • Waterproofing of concrete and metal roof surfaces.
  • Protection of commercial and residential buildings against UV exposure.
  • Application on terraces, balconies and exposed roof slabs.
  • Protective coating over new or existing cementitious substrates.
  • Sealing surfaces exposed to wind-driven rain and harsh weather conditions.

DRYING TIME

Times assume (21Β° C) and 50% relative humidity.

  • To touch: 1–2 hours
  • To recoat: minimum of 6 hours

Lower surface or air temperatures and higher relative humidity will extend the drying time.

STORAGE

  • Keep the products packed in a dry place.
  • Keep away from direct sunlight.
  • Do not place the pallets on top of each other.
  • Rolls must always be kept in a vertical position.

ADVANTAGES

  • 100% acrylic to protect and waterproof commercial and residential buildings
  • Breathable to allow water vapor to escape
  • Excellent adhesion, bonds securely to concrete and metal substrate for long-term durability.
  • Low VOC content for broad compliance across all regions Water repellent.
  • Highly UV resistance.
  • Highly resistance to cl– ions and CO2 gas.
  • Easy to apply and dries quickly.
  • Penetration into concrete is very well.
  • Highly resistance to chemicals.
  • Excellently adhered on concrete and metal.
  • Requires no lining.

SURFACE PREPARATION

  • Surfaces should be clean and sound and free of all bond-inhibiting contaminants.
  • Concrete substrates should be fully cured.
  • Repair any holes, spalled and damaged concrete with appropriate repair materials. Allow appropriate cure time prior to coating.
  • Remove any protruding concrete accessories and smooth out any surface irregularities.

PRE-CAUTION

  • Do not apply when substrate or ambient temperature is (4Β° C) or below or is expected to fall below (4Β° C) within 24 hours after application.
  • Do not apply if rain is expected within 24 hours of application.

TOOL CLEANING

Clean all tools immediately with clean water.

APPLICATION

  • Once the mixing is ready apply a two–coat system, achieving a total dry-film thickness (DFT) (0.3–0.4 mm).
  • Apply Roofcryl by brush, spray, roller, or spray-and-backroll.

THICKNESS

Available as a two-coat system achieving a total dry film thickness of approximately 0.3 – 0.4 mm.

PACKAGING

18-kg. per pail, white color.

MIXING

Prior to use, mix Roofcryl at slow speed with drill and mixing paddle to ensure uniform color and to minimize air entrapment.

APPLICATION TOOLS AND EQUIPMENT

Roller:

  • Use a quality ΒΎ – 1 ΒΌ nap roller cover.
  • Completely saturate the roller andkeep it loaded with the coating to build the required miles. Never dry roll.
  • Cross roll, maintaining a wet edge, to achieve uniform thickness. Backroll in one direction
  • for consistent appearance.

Brush:

  • Application by brush is recommended only for small inaccessible areas, (e.g., on touch-ups.)
  • Use only a nylon brush.

HEALTH, SAFETY AND ENVIRONMENT

All safety measures should be observed during application. Fire extinguishers should be available on site. Care should be taken with gas, and torches should not be rested on finished surface or on any materials that can be scratched by flame or hot torch. Gloves and goggles should be worn by all workers during application.

Read, understand and follow all Material Safety Data Sheets and product label information for this product prior to use.

TECHNICAL SUPPORT

International Insulation Company (IIC) – Bitugulf technical support team consist of expert engineers offers a comprehensive service support to specifiers, end users and contractors, and on-site technical assistance.

Note: The technical data provided reflects typical properties based on laboratory tests and practical experience, subject to UEAtc tolerance levels. While we cannot guarantee performance under all conditions, further details are available upon request, with a standard variation of up to 20%.

TECHNICAL DATA