BITUFLAME - SL

Request a Quote
Download TDS

DESCRIPTION

Bituflame SL is high performance waterproofing membrane, produced with a layer of natural slate flakes on weathering side to protect the membrane from UV radiation and ageing. Produced in highly controlled process, the reinforcement made of nonwoven spunbonded polyester and straight run bitumen modified with selected APP polymers and stabilizers.

SPECIFICATION

BITUFLAME-SL is a torch-applied APP modified bitumen waterproofing membrane reinforced with non-woven polyester and surfaced with natural slate flakes for UV protection. The membrane complies with ASTM D 6222 and offers high tensile strength, excellent elongation, dimensional stability, and resistance to heat, ageing, and water penetration. It is supplied in standard 10 m Γ— 1 m rolls and is suitable for exposed waterproofing applications.

APPROVALS / CERTIFICATES

The manufacturing facility is certified with the ISO 9001:2015 QMS, GMP ISO 14001 EM and ISO 45001 O H & S .

USES

Bituflame SL is ideal to use for new and re- roofing applications. It can be used in almost every waterproofing application which includes:

  • roofs
  • balconies
  • basements
  • reservoirs
  • bridges
  • tunnels
  • lining for sewage canals
  • sub-grade structures etc.

STORAGE

  • Keep the products packed in a dry place.
  • Keep away from direct sunlight.
  • Do not place the pallets on top of each other.
  • Rolls must always be kept in a vertical position

FEATURES

  • Positive barrier to water and dampness
  • Excellent resistance to ageing and atmospheric agents
  • Accommodates structural movements
  • Designed for use in exposed system
  • Provided with lap strip
  • Resistant to water-born chemical attack
  • Stability at high temperatures
  • Excellent puncture and tear resistance
  • Excellent resistance to UV rays, aging and
  • weathering
  • Easy for application and repair works

SURFACE CLEANING

The surface must be thoroughly cleaned and should be free from dust, debris, oil and protruding elements.

FIXING INSTRUCTION

The installation should start from one edge/end of the surface. Unroll one roll over the surface with minimum 10 cm side lap alignment. Fixing should be either loose laid or fully bonded.

Loose Laid:
Re-roll the unrolled membrane to a length suitable for application
without changing the orientation. Melt minimum 10 cm from the edges.
Fix the melt portion firmly to the pre-primed surface. Position the
subsequent rolls, give edge overlapping of minimum 10 cm, side
overlapping of minimum 10 cm and continue until the area is fully fixed.
The melted compound should be spread with a trowel or roller to ensure
a smooth tight seal.

Fully Bonded:
Melt the lower surface of the membrane with a gas torch by moving the
flame across the entire width of the roll. Fix the melt portion firmly to the
pre-primed surface. The subsequent rolls should be done in the same
manner as of loosed laid membrane.

THICKNESS

Membrane available in different thicknesses (3, 5, 6 mm)

PRIMING

Apply one coat of the recommended primer and we recommend using Sealcoat D41. Allow the primer coat to dry until it is tack free. Prior to application of the membrane, all surfaces must be re-primed if left more than 24 hours.

APPLICATION TOOLS AND EQUIPMENT

  • Propane gas torch with related gas cylinder
  • Knife / Cutter
  • Trowel with a rounded tip
  • Protective gloves and goggles
  • Marking aids
  • Measuring tape
  • Fire extinguisher

HEALTH, SAFETY AND ENVIRONMENT

All safety measures should be observed during application. Fire extinguishers should be available on site. Care should be taken with gas, and torch should not be rested on finished surface or on any materials that can be scratched by flame or hot torch. Gloves and goggles should be worn by all workers during application.

Read, understand and follow all Material Safety Data Sheets and product label information for this product prior to use.

TECHNICAL SUPPORT

International Insulation Company (IIC) – Bitugulf technical support team consist of expert engineers offers a comprehensive service support to specifiers, end users and contractors, and on-site technical assistance.

Note: The technical data provided reflects typical properties based on laboratory tests and practical experience, subject to UEAtc tolerance levels. While we cannot guarantee performance under all conditions, further details are available upon request, with a standard variation of up to 20%.

TECHNICAL DATA